How to Select M8 Connectors for Sensors and Industrial Equipment
Quick answer: Selecting an M8 connector requires matching five factors to the application: pin count, coding, connector gender and orientation, termination style, and electrical/environmental ratings.
M8 connectors defined by IEC 61076-2-104 provide a compact interface for sensors, actuators, and industrial devices where installation space is limited. This buyer’s guide uses specifications from the KRONZ M8 connector range to explain how to compare available options and avoid common ordering mistakes.
What Is an M8 Connector?
An M8 connector is a compact circular connector with an 8 mm threaded coupling. It is smaller than an M12 connector and is commonly used for sensor-level wiring, compact actuators, distribution systems, and field devices installed in space-constrained equipment.
The referenced KRONZ range includes 3-, 4-, 5-, and 6-pin products in straight and angled configurations. Available options include A-coded connectors, a B-coded 5-pin version, field-wireable connectors with screw contacts, and pre-molded PVC cable assemblies.
| Parameter | Specification | Buyer’s Note |
|---|---|---|
| Applicable standard | IEC 61076-2-104 | Confirm that both mating sides use the same M8 interface and coding. |
| Pin counts | 3 / 4 / 5 / 6 in the referenced product range | Select according to the device wiring diagram, not connector size alone. |
| Coding | A-code; B-code on the referenced 5-pin variant | Different coding arrangements are mechanically incompatible. |
| Rated current | 3 A on referenced cable assemblies such as M0803M-5/P00K | Check the individual product datasheet before ordering. |
| Rated voltage | 3/4-pin: 60 V 5/6/8-pin: 30 V |
Voltage varies by pin count and product configuration. |
| Contact resistance | ≤ 5 mΩ | Applies to the referenced M8 series. |
| Insulation resistance | ≥ 100 MΩ | Applies to the referenced M8 series. |
| Coupling nut | Nickel-plated brass | Provides a threaded mechanical connection. |
| Contacts | Gold-plated brass | Designed for reliable low-level signal connections. |
| Contact carrier | Black PA | Verify suitability if the application has special chemical requirements. |
| Housing | Black TPU | Product-specific construction should be checked for moving-cable applications. |
| Seal | FPM/FKM | Ingress protection depends on correct mating and installation. |
| Ingress protection | IP67 | Rating applies when the connector is properly assembled and mated. |
| Ambient temperature | -25 to +85 °C | Also check the connected sensor’s temperature rating. |
| Pollution degree | 3 | Suitable for industrial environments within the specified product conditions. |
Compared with M12, the smaller M8 footprint allows more interfaces to fit on a compact panel or device housing. That makes M8 particularly useful for rows of sensors and other low-power field devices where space is more important than high pin capacity or higher power handling.
Step 1: Match the Pin Count to the Device Wiring
Pin count is the first practical filter. Start with the sensor or device wiring diagram and count the required power, signal, diagnostic, and communication conductors.
3-Pin M8 Connectors
Three-pin M8 connectors are commonly used for standard DC three-wire sensors with power, ground, and one switching output.
- M0803M-5/P00K: straight male, A-coded, 5 m PVC cable, rated current 3 A.
- M0803M-2/POOR: straight male, A-coded, 2 m cable.
- Referenced wire assignment for M0803M-5/P00K: pin 1 = BN, pin 3 = BU, and pin 4 = BK.
4-Pin M8 Connectors
A 4-pin connector can accommodate a second output, complementary signal, or diagnostic conductor, depending on the device. It is one of the most flexible formats for industrial sensor wiring.
- M0804F-2/P00R: straight female, A-coded, pre-molded cable.
- M0804M-2/POOR: straight male, A-coded, pre-molded cable.
- M0804FA-2/POOR: angled female for installations requiring a 90-degree cable exit.
5-Pin M8 Connectors
Five-pin connectors may be selected for devices that require additional signal conductors or a specific keyed wiring interface. The referenced range includes the B-coded M0805BM-2/POOR.
6-Pin M8 Connectors
Six-pin M8 connectors provide higher signal density in a small footprint. The referenced M0806M-2/P00R uses six 0.14 mm² conductors, equivalent to 26 AWG, and is rated at 30 V.
Step 2: Confirm the Coding
Coding uses a mechanical key to prevent incompatible connections. The connector coding must match the device port exactly.
- A-coded M8: used by the referenced 3-, 4-, and 6-pin sensor and actuator connectors.
- B-coded M8: used by the referenced 5-pin M0805BM-2/POOR and mechanically distinguished from A-coded interfaces.
Step 3: Choose the Correct Gender and Orientation
Male or Female
Connector gender refers to the contact interface, not the external threaded body. A sensor may present male contacts while the cable assembly provides the mating female contacts, but the actual device interface must always be verified.
When preparing a purchase specification, state all three items together:
- Device-side connector gender
- Required cable-side connector gender
- Pin count and coding
Straight or Angled
- Straight connectors are generally suitable for open cable routes with enough clearance behind the device.
- Angled connectors provide a 90-degree cable exit and can reduce the required installation depth behind machine frames, sensors, and shallow enclosures.
For example, the straight female M0804F-2/P00R suits an unobstructed cable route, while the angled female M0804FA-2/POOR is better suited to restricted rear clearance.
Step 4: Select Field-Wireable or Pre-Molded Termination
| Connector Style | Referenced Example | Advantages | Best-Fit Applications |
|---|---|---|---|
| Field-wireable | H0804FV-0, 4-pin straight female with screw connection | Can be installed on a custom-cut cable and replaced on site | Repairs, retrofits, prototypes, and variable cable routes |
| Pre-molded cable | M0803M-5/P00K and M0804M-2/POOR | Factory-molded construction with integrated strain relief and consistent assembly | Production machines, fixed installations, and fast deployment |
Field-wireable connectors are useful when cable lengths cannot be finalized in advance or when maintenance teams need to repair damaged wiring locally. Pre-molded assemblies reduce installation steps and are often the more efficient option for repeat-build equipment.
Standard pre-molded cable lengths include 2 m, 5 m, and 10 m. Customized cable lengths are supported with a stated minimum order quantity of 20 pieces.
Step 5: Verify Voltage, Current, and Environmental Ratings
Mechanical compatibility does not guarantee electrical suitability. Compare the connector rating against the circuit voltage, expected current, installation temperature, and exposure conditions.
Voltage Ratings by Pin Count
| Configuration | Rated Voltage |
|---|---|
| Standard 3-pin M8 | 60 V |
| Standard 4-pin M8 | 60 V |
| Standard 5-pin M8 | 30 V |
| Standard 6-pin M8 | 30 V |
| Standard 8-pin M8 | 30 V |
| Shielded 3/4/5-pin M8 | 60 V |
| Shielded 6/8-pin M8 | 30 V |
Other Referenced Ratings
- Rated current: 3 A on referenced assemblies such as M0803M-5/P00K.
- Contact resistance: ≤ 5 mΩ.
- Insulation resistance: ≥ 100 MΩ.
- Ingress protection: IP67 when correctly assembled and mated.
- Ambient temperature: -25 to +85 °C.
- Pollution degree: 3.
- Construction: nickel-plated brass coupling nut, gold-plated brass contacts, PA contact carrier, TPU housing, and FPM/FKM sealing.
IP67 supports use in dusty or wet industrial environments under the rating’s specified test conditions. It does not mean every connector is suitable for continuous submersion. Applications requiring continuous underwater operation should use a product explicitly rated for that condition.
Practical M8 Connector Selection for Sensors
The M8 format is particularly well suited to compact inductive sensors. The referenced IS2 sensor series uses an integrated M8 interface, allowing the sensor to be replaced without removing the complete field cable.
| Sensor | Output | Referenced Specifications | Suggested Mating Interface |
|---|---|---|---|
| IS2-M8PC60-S0B/D | PNP, normally open | 2 mm detection distance, 220 mA overload protection, 3 kHz, 10–30 V DC | Matching 3- or 4-pin M8 A-coded cable, subject to the sensor pinout |
| IS2-M8NO60-S0B/D | NPN, normally open | 2 mm quasi-flush sensing, stainless steel housing, 3 kHz, 0.1 ms response | Matching 3- or 4-pin M8 A-coded cable, subject to the sensor pinout |
| IS2-M8NC60-S0B/D | NPN, normally closed | 2 mm quasi-flush sensing, POM sensing surface, IP67, -25 to +70 °C | Matching 3- or 4-pin M8 A-coded cable, subject to the sensor pinout |
Recommended Sensor-Drop Selection Process
- Read the sensor wiring diagram. Identify PNP or NPN output, NO or NC switching logic, conductor count, and pin assignment.
- Confirm the connector family. Verify that the device port is M8 rather than M12 or a terminal connection.
- Check coding and gender. Both must match the installed device port.
- Choose straight or angled. Base the decision on available clearance and cable routing.
- Select the termination. Choose a standard 2 m, 5 m, or 10 m molded cable, a custom length, or a field-wireable connector.
- Verify ratings. Confirm voltage, current, temperature, and ingress protection against the actual operating environment.
This approach is suitable for compact machinery with multiple sensor drops, including packaging equipment, semiconductor handling systems, textile machines, and other automated equipment where panel and routing space are limited.
M8 Splitters for Multi-Sensor Wiring
A splitter allows one connection path to branch into two sensor connections, helping reduce cable runs in distributed field wiring. The available M8 splitter data includes PVC and PUR cable options.
| Item | PVC Version | PUR Version |
|---|---|---|
| Standard model | YKM4-2F3-2-2/P00K/L04 | YKM4-2F3-0.2-0.2/P01K/L04 |
| Cable material | Black PVC | Black PUR |
| Available cable lengths | 0.2 m, 2 m, or customized length | |
| Rated current | 4 A | |
| Rated voltage | 250 V | |
| Ingress protection | IP67 | |
| Compliance | RoHS compliant | |
The range also includes cross-size distribution products such as the M12-to-dual-M8 YWM4-2BF3/L04, which uses gold-plated contacts and an M12 interface compliant with IEC 61076-2-101.
M8 Connector Purchasing Checklist
- Confirm that the device interface is M8.
- Match the exact pin count required by the wiring diagram.
- Verify A-code or B-code.
- Specify the mating gender correctly.
- Choose straight or angled cable exit based on installation clearance.
- Select field-wireable or pre-molded termination.
- Choose a 2 m, 5 m, or 10 m standard cable, or request a custom length.
- Check rated voltage and current for the selected pin count and model.
- Confirm IP67 and temperature suitability for the installation.
- Decide whether shielding is required.
- Check whether a splitter is needed for multi-sensor wiring.
- Provide the device pinout when requesting a matching recommendation.
Quick Comparison Table
| Selection Point | Available Options | Question to Ask |
|---|---|---|
| Pin count | 3 / 4 / 5 / 6 in the referenced range | How many conductors and functions does the device require? |
| Coding | A-code or B-code | What coding is specified on the device port? |
| Gender | Male or female | Which mating contact interface is required? |
| Orientation | Straight or angled | How much clearance is available behind the device? |
| Termination | Field-wireable or pre-molded | Is factory assembly or on-site flexibility more important? |
| Cable length | 2 m / 5 m / 10 m / customized | What route length is required without excess cable? |
| Voltage | 60 V for specified lower pin counts; 30 V for specified higher pin counts | Does the selected model cover the circuit voltage? |
| Environment | IP67, -25 to +85 °C for the referenced series | Will the connection face dust, moisture, coolant, or temperature extremes? |
| Branching | M8 and M12-to-M8 splitters | Does one cable route need to serve multiple devices? |
Frequently Asked Questions
What is the main difference between M8 and M12 connectors?
M8 connectors use a smaller 8 mm threaded coupling and are commonly selected for compact sensor connections. M12 connectors use a larger 12 mm coupling and offer broader options for power, signal, and industrial communication applications. Selection should be based on the device interface and required electrical performance rather than size alone.
Are M8 connectors waterproof?
The referenced M8 products are rated IP67 when correctly assembled and mated. This provides protection against dust and temporary water exposure under the rating’s test conditions. IP67 should not be treated as approval for continuous submersion.
Can an A-coded M8 connector mate with a B-coded connector?
No. The mechanical keying differs, preventing A-coded and B-coded connectors from mating. Coding must be checked before ordering.
Can an M8 connector be wired in the field?
Yes. Field-wireable products such as the H0804FV-0 use screw termination and can be installed on custom-cut cable for repairs, retrofits, and prototype equipment.
What pre-molded cable lengths are available?
Standard cable lengths are 2 m, 5 m, and 10 m. Customized lengths are supported with a stated minimum order quantity of 20 pieces.
Should I use a straight or angled M8 connector?
Use a straight connector when there is enough rear clearance and the cable can run directly away from the device. Choose an angled connector when installation depth is limited or a 90-degree cable exit provides better routing.
Does the connector pin count determine its voltage rating?
Pin count is one factor. The supplied ratings specify 60 V for standard 3- and 4-pin versions and 30 V for standard 5-, 6-, and 8-pin versions. For shielded types, 3-, 4-, and 5-pin versions are rated 60 V, while 6- and 8-pin versions are rated 30 V. Always verify the individual product datasheet.
What information should be provided for a matching recommendation?
Provide the device model, connector size, pin count, coding, port gender, pin assignment, required cable length, preferred cable material, operating voltage and current, and environmental conditions.
Conclusion
Selecting an M8 connector is a five-step process: match the pin count, verify the coding, specify the correct gender and orientation, choose the appropriate termination style, and confirm all electrical and environmental ratings.
For many sensor applications, the result will be a 3- or 4-pin A-coded cable assembly matched to the device pinout. However, coding, voltage rating, cable material, shielding, orientation, and branch requirements must still be reviewed before an order is placed.
Browse the KRONZ M8 connector range, or submit your sensor list and wiring requirements for a model-matching recommendation. Standard pre-molded lengths include 2 m, 5 m, and 10 m, while customized lengths are available with a minimum order quantity of 20 pieces.

